EF-008
6S 22.2V 150A Inspection & Mapping Drone BMS
For 6S1P 22.2V 22Ah 6S2P 22.2V 44Ah Lithium Polymer drone battery pack
EF-008 Support
- Constant working current: 150A
- Two battery packs in parallel
- Over Discharge Current alarm,no protection: 600A
- Customized BMS solution
Product Introduction
The EF-008 is a customized 6S Battery Management System for inspection, mapping, patrol, training, and light-route UAV battery packs. It supports 22.2V LiPo and compatible 23.7V high-voltage semi-solid battery configurations, with up to 150A continuous discharge and 60A continuous charge.
The BMS uses a shared charge/discharge port and integrates four temperature sensing channels: three battery NTC probes and one MOSFET temperature sensor. It supports battery parallel connection, pre-discharge, power switch control, LED status indication, configurable protection, battery heating, and onboard history storage.
Communication is available through isolated CAN and isolated RS485 interfaces, with project-specific protocol configuration available. The board operates from -30°C to 70°C and has a compact size of 130 × 95 × 15 mm (±1 mm).
| Battery packs compatible with the 6S 150A BMS | |
|
10C 6S1P 22.2V 22000mAh Soft Pack UAV Battery
15C 6S1P 22.2V 12000mAh LiPo UAV Battery
25C 6S1P 22.2V 20000mAh LiPo UAV Battery
25C 6S1P 22.2V 30000mAh LiPo UAV Battery
25C 6S1P 22.2V 22000mAh LiPo UAV Battery
25C 6S1P 22.2V 16000mAh LiPo UAV Battery
30C 6S1P 22.2V 16000mAh LiPo UAV Battery
High Voltage Semi-Solid 6S1P 23.7V 24500mAh UAV Battery
High Voltage Semi-Solid 6S1P 23.7V 28500mAh UAV Battery
6S1P 22.2V 22000mAh Soft Pack UAV Battery
|
|
| Drones compatible with the aforementioned battery pack | |
| Inspection & Mapping Drone / Surveillance & Patrol Drone / Training Drone / Light Route Mission UAV | |
| Key Features | |
| LiPo and semi-solid battery pack support | Battery status (Normal / Warning / Fault); HMI |
| Battery historical data query | Intelligent dynamic balancing |
| Real-time individual cell monitoring | Battery self-heating function |
| Dual overvoltage protection (cell + pack); undervoltage protection (cell + pack) | Voltage tolerance ≤ ±5mV |
| Temperature error ≤ ±2°C | Power calculation error ≤ ±5% |
| Overcurrent protection; short circuit protection; reverse charge protection | |
Engineering Validation and Testing
Host Communication Testing
Verifies real-time battery-data acquisition, parameter response and communication stability under representative operating conditions.
Over-Discharge Protection Testing
Validates cell-voltage monitoring, protection thresholds and fault responses under low-voltage conditions.
Over-Charge Protection Testing
Validates cell-voltage monitoring, configurable protection thresholds and balancing behaviour during charging.
Standby Power Consumption Testing
Measures active-mode and sleep-mode current consumption to support battery-storage evaluation.
Technical FAQ for EF-008 Integration
short-circuit and temperature protection. Protection thresholds can be
configured according to the selected battery chemistry, pack configuration
and UAV application requirements.
Industry Experience
Clients Served
Countries Covered
Technical Specifications
Smart Battery Management System for 6S Lithium Polymer UAV / Drone Battery Packs
| Battery Type | 6S LiPo / high-voltage semi-solid UAV battery pack |
| Continuous discharge current | 150 A |
| Continuous charge current | 60 A |
| Communication | CAN,UART,DroneCAN,MODBUS,RS485,BLE |
| Pre-Discharge | Standard |
| Packs in Parallel | 2 battery packs |
| Parameter Item | MIN | TYP | MAX | Unit | |
|---|---|---|---|---|---|
| Single Cell Over-Charge Protection | Over-Charge Protection Voltage | 4.38 | 4.40 | 4.42 | V |
| Over-Charge Protection Delay Time | 2000 | 3000 | 4000 | ms | |
| Over-Charge Release Voltage | 4200 | 4200 | 4200 | mV | |
| SAFETY ALERT Total overvoltage turns off the charging MOS. | |||||
| Single Cell Over-Discharge Protection | Over-Discharge Protection Voltage | 2.40 | 2.50 | 2.60 | V |
| Over-Discharge Protection Delay Time | 1000 | 1500 | 2000 | ms | |
| Over-Discharge Release Voltage | 2.90 | 3.00 | 3.10 | V | |
| SAFETY ALERT Over-discharge voltage: warning only - no hardware cutoff. | |||||
| Parameter Item | MIN | TYP | MAX | Unit | |
|---|---|---|---|---|---|
| Over-Charge Current Protection | Over-Current Charge Protection Threshold | 85 | 90 | 95 | A |
| Over-Current Charge Protection Delay Time | 3000 | 5000 | 7000 | ms | |
| Over-Current Charge Protection Release | Delay 30 s self-recovery; after 3 consecutive trips, charger must be disconnected to restore. | ||||
| Over-Discharge Current Protection | 1st-Level Over-Current Protection Threshold | 280 | 300 | 320 | A |
| 1st-Level Over-Current Protection Delay Time | 400 | 600 | 800 | ms | |
| SAFETY ALERT 1st-level discharge over-current: warning only - no hardware cutoff. | |||||
| 2nd-Level Over-Current Protection Threshold | 600 | 625 | 650 | A | |
| 2nd-Level Over-Current Protection Delay Time | 10 | 20 | 100 | ms | |
| SAFETY ALERT 2nd-level discharge over-current: warning only - no hardware cutoff. | |||||
| Over-Current Discharge Release | Over-Current Discharge Protection Release | Delay 30 s self-recovery; after 3 consecutive trips, load must be disconnected to restore. | |||
| Parameter Item | MIN | TYP | MAX | Unit | |
|---|---|---|---|---|---|
| Charging Temperature Protection | Charging High-Temperature Protection | 60 | 65 | 70 | °C |
| Charging High-Temperature Release | 50 | 55 | 60 | °C | |
| Charging Low-Temperature Protection | -10 | -5 | 0 | °C | |
| Charging Low-Temperature Release | 5 | 10 | 15 | °C | |
| Discharging Temperature Protection | Discharging High-Temperature Protection | 60 | 65 | 70 | °C |
| SAFETY ALERT Warning only - no hardware cutoff. | |||||
| Discharging High-Temperature Release | 55 | 60 | 65 | °C | |
| Discharging Low-Temperature Protection | -25 | -20 | -15 | °C | |
| SAFETY ALERT Warning only - no hardware cutoff. | |||||
| Discharging Temp Release | Discharging Low-Temperature Release | -20 | -15 | -10 | °C |
| Parameter Item | MIN | TYP | MAX | Unit | |
|---|---|---|---|---|---|
| MOS Temperature Protection | MOS High-Temperature Protection Value | 85 | 90 | 95 | °C |
| MOS Release Temperature | 65 | 70 | 75 | °C | |
| Heating Management | Heating Activation Temperature | - | 0 | - | °C |
| Heating Deactivation Temperature | - | 10 | - | °C | |
| Heating Current | - | < 5 | - | A | |
| Heating Mode | Charging-activated | ||||
Key Features
High-current battery management, configurable protection, and communication integration for 6S inspection, mapping, patrol, training, and light-route UAV battery systems.
High Voltage Semi-Solid 6S Battery Support
Designed for 6S LiPo and high voltage semi-solid UAV battery packs, including 6S1P 23.7V 24500mAh battery configurations for inspection, mapping, patrol, training, and light-route drones.
150A Continuous Discharge Capability
Supports up to 150A continuous discharge and 60A continuous charge, meeting the high-current requirements of compact UAV battery systems.
CAN Communication for UAV Integration
Provides isolated CAN communication for real-time battery status reporting, fault alerts, SOC data, and integration with UAV flight-control or power-management systems.
Configurable Protection Parameters
Supports configurable over-charge, over-discharge, over-current, short-circuit, and temperature protection according to battery chemistry, pack design, and UAV operating conditions.
Parallel Battery Pack Support
Can support two battery packs in parallel, helping UAV platforms extend flight endurance while maintaining battery-status monitoring and protection logic.
4-Point Temperature Monitoring
Equipped with 3 battery NTC sensors and 1 MOS temperature sensor for real-time thermal monitoring and safer operation under high-current discharge conditions.
Low-Temperature Heating Control
Supports charging-activated battery heating control for cold environments, helping improve battery readiness during low-temperature UAV operations.
PC and Optional Wireless Diagnostics
Parameters, fault records, battery status, and protection settings can be checked or configured through PC tools, with optional BLE support for mobile monitoring and diagnostics.
Applications
Powering 6S UAV battery systems for inspection, mapping, patrol, training, and light-route missions
Inspection & Mapping Drones
Provides stable battery-status monitoring and configurable protection for aerial inspection, surveying, mapping, and route-planning UAV platforms.
Surveillance & Patrol Drones
Supports 6S UAV battery packs used in security patrol, facility inspection, border monitoring, and outdoor surveillance missions.
Training Drones
Designed for high-current 6S training UAV battery systems that require reliable protection, CAN communication, and clear battery-status feedback.
Light Route Mission UAVs
Suitable for compact UAV platforms performing predefined route missions, with support for 150A continuous discharge and real-time battery telemetry.
Detection & Monitoring UAVs
Helps manage battery safety and operating status for detection, monitoring, and data-collection drones used in industrial or outdoor environments.
High Voltage Semi-Solid Battery UAVs
Can be configured for high voltage semi-solid 6S1P UAV battery packs, including 23.7V 24500mAh battery applications, subject to engineering confirmation.
EF-008 6S Inspection & Mapping Drone BMS
Request EF-008 Technical Proposal
Share your 6S UAV battery pack details and our engineers will confirm the EF-008 configuration for 22.2V LiPo or 23.7V high voltage semi-solid battery packs, 150A continuous discharge, 60A charging, communication interfaces, and protection logic.
- 6S1P 22.2V LiPo or 6S1P 23.7V high voltage semi-solid UAV battery pack
- 150A continuous discharge and 60A continuous charge requirements
- CAN 2.0B, isolated UART, optional RS485, DroneCAN, MODBUS or BLE needs
- Parallel battery pack, pre-discharge protection, heating and NTC monitoring details
Send Project Details
EF-008 battery pack, protocol and protection requirements