AYAA · SMART POWER FOR UAVs
EF-006 12S 81A Smart UAV BMS
EF-006 is a smart BMS for 12S UAV lithium battery packs, supporting 81A continuous discharge and 27A charging through one port. It monitors cell voltage, current, and temperature, and provides passive balancing, isolated CAN, Bluetooth, and battery history. In flight, voltage, current, and temperature anomalies are reported as alerts rather than triggering protection.
Is EF-006 Right for Your 12S UAV Battery Pack?
12S CONFIGURATION CHECK
Match the pack before integration.
Compare your 12S pack chemistry, charge-voltage limit, current demand, CAN requirements and installation space with the EF-006 specification.
12S1P · 44.4V NOMINAL
12S1P battery pack options for EF-006
EF-006 12S 81A Smart UAV BMS
Monitors cell voltage, current and temperature in 12S UAV packs. It supports
27A continuous charging, passive balancing, isolated CAN, Bluetooth and battery history.
During flight, anomalies are reported as alerts rather than protective shutdown.
ENGINEERING SPECIFICATIONS
EF-006 Key Specifications
EF-006 is a 12S smart UAV BMS with a common charge/discharge port. Review the 50.4 V charging voltage, continuous-current limits, balancing, communication and installation dimensions before pack integration.
| Battery and Electrical Configuration |
Specification |
|---|---|
| Product Model | EF-006 |
| Battery Pack Configuration | 12S |
| Charging Voltage | 50.4 V |
| Continuous Charging Current | 27 A |
| Continuous Discharging Current | 81 A |
| Port Configuration | Common charge/discharge port |
| Output Mode | MOSFET |
| Operating Temperature | −20°C to 70°C |
| Dimensions | 123.8 × 94.8 × 11 mm (±1 mm) |
| PCBA Coating | Conformal coating |
| Voltage/Current/Temperature Response | Ground protection; in-flight alerts only |
| Monitoring, Balancing and Communication |
Specification |
|---|---|
| NTC Temperature Sensors | 3 battery channels + 1 MOS channel |
| Balancing Method | Passive |
| Balancing Current | 50 mA typical (40–60 mA) |
| Balancing Start Voltage | 3.8 V typical |
| Balancing Start Difference | 50 mV typical |
| CAN Communication | Isolated; 1 Mbps; default BMS ID 1 |
| CAN Termination | 120 Ω resistor included |
| BLE Communication | Standard; 115200 baud; ID 1 |
| Operating Consumption | ≤10 mA |
| Sleep Consumption | ≤3 mA (BLE operating) |
| Deep-Sleep Consumption | ≤50 µA (cell undervoltage) |
Protection, Communication & Battery Intelligence
Four operating scenarios for security-surveillance and border-patrol UAVs: in-flight temperature warning, anti-spark precharge, multi-protocol communication and high-accuracy SOC estimation.
IN-FLIGHT HIGH-TEMPERATURE WARNING
During flight, a high-temperature discharge condition triggers a warning without interrupting discharge.
PRECHARGE BEFORE MAIN-CIRCUIT CONNECTION
Reduce the voltage difference before the main circuit closes to limit inrush current and connector arcing.
MULTI-PROTOCOL COMMUNICATION
Support data exchange between the BMS, flight-control system and external engineering devices.
HIGH-ACCURACY IN-FLIGHT SOC ESTIMATION
Estimate the remaining battery capacity during flight to support mission and return planning.
CONNECTED BATTERY DATA
CAN Communication, Host Software & Battery Data
Connect EF-006 through isolated CAN and view battery status through host software or BLE.
Confirm the flight-controller protocol and CAN configuration before integration.
Product Demonstration
EF-006 Bench Demonstration: Host Software & CAN
See the EF-006 bench setup, host-software battery display and CAN tool interface. Use the engineering checklist to review your own 12S pack integration.
Standard EF-006 or Custom UAV BMS?
Choose EF-006 for a matching 12S UAV battery project, or share requirements outside its standard configuration for an engineering review.
Choose Standard EF-006
A 12S smart BMS platform for UAV battery projects that match its electrical, communication and installation requirements.
- 12S battery-pack configuration
- 27A continuous charge and 81A continuous discharge
- Isolated CAN and BLE communication
- Cell monitoring, passive balancing and history storage
Discuss a Custom BMS
For battery packs, interfaces or control requirements outside the standard EF-006 configuration.
- Different cell count or battery chemistry
- Project-specific current or wiring requirements
- Custom communication or protocol requirements
- Project-specific hardware or software settings
Technical Resources, Support & Warranty
Download the EF-006 datasheet for electrical specifications, wiring, interfaces and setup guidance, or contact engineering support for project and warranty questions.
Get Product Specification
12S 81A UAV BMS specifications, dimensions, connection sequence, port definitions, protection settings and communication details.
Download Datasheet →Wiring & Port Sequence
Review B−, B1–B12, P−, P+, CAN and NTC temperature connections before power-on.
Open Datasheet → System ConnectionCAN & Host Software
Review isolated CAN, 1 Mbps communication, BMS ID, BLE and battery-data functions.
Open Datasheet → Engineering SupportIntegration Checklist
Prepare battery chemistry, maximum voltage, current profile, connector layout, flight-controller protocol and installation space.
Contact Engineering → WarrantyWarranty & Service
The EF-006 specification states a 12-month warranty for quality issues under normal use. Confirm the terms for your project.
Contact Support →EF-006 12S Battery Pack Engineering FAQ
Are all listed 12S1P battery packs ready to use with EF-006?+
The listed 44.4 V nominal packs include smart and LiPo, semi-solid, and high-voltage semi-solid options. Matching 12S1P does not establish electrical compatibility by itself. Confirm each pack's chemistry, maximum charging voltage, continuous and peak current, connector layout, and installation space before integration. High-voltage semi-solid packs need a specific charging-voltage review.
Does a 25C rating or higher pack capacity increase the EF-006 current limit?+
No. The pack's C rating and capacity describe the battery, while this EF-006 configuration is specified for 27 A continuous charging and 81 A continuous discharging. Compare the UAV's actual continuous load, peak-current duration, charger output, cables, and connectors with those limits. Ask for an engineering review if the project needs more current.
How should the 12S voltage-sensing and power connections be checked?+
In the EF-006 pin definitions, GND and B0 connect to cell 1 negative; B1 through B12 connect to the positive side of their corresponding cells. The charge and discharge paths share a port with P+ and P− terminals. Check cell order, polarity, connector pinout, and the complete wiring diagram in the EF-006 specification before applying power.
What must match for the flight controller to read EF-006 CAN data?+
EF-006 provides isolated CAN at 1 Mbps with default BMS ID 1, and its CAN interface includes a 120 Ω termination resistor. Confirm the flight controller's message protocol, signal mapping, bus wiring, and termination arrangement during integration. A matching CAN connector and baud rate alone do not confirm protocol compatibility.
When does EF-006 passive balancing start?+
The typical balancing start voltage is 3.8 V per cell, with a typical 50 mV cell-voltage difference condition. Typical passive balancing current is 50 mA. Check initial cell matching and pack behavior separately; the balancing function is not a substitute for confirming that the cells and pack design are suitable.
Will EF-006 disconnect the battery when an anomaly occurs during flight?+
The EF-006 specification describes protection against voltage, current, and temperature anomalies during ground operation. During flight, those anomalies are reported through alarms and communication data without triggering protective shutdown. The flight controller and operating procedure should account for those alerts.
EF-006 vs EF-007 vs EF-013: Compare 12S UAV BMS Options
All three models support 12S battery packs. Compare continuous charge and discharge current, heating, balancing and interfaces, then confirm your pack chemistry, wiring and flight-controller protocol.
| Selection Factor |
EF-006
12S 81A Smart UAV BMS
|
EF-007
12S 120A Smart UAV BMS
|
EF-013
12S 150A Smart UAV BMS
|
|---|---|---|---|
| Best-Fit UAV Application | 12S inspection and detection UAVs within the 81 A continuous discharge rating | 12S inspection or mapping UAVs needing 120 A continuous current or battery heating | 12S inspection or surveillance UAVs needing 150 A continuous discharge |
| Supported Battery Configuration | 12S | 12S | 12S |
| Nominal Pack Voltage | 44.4 V | 44.4 V | 44.4 V |
| Continuous Charging Current | 27 A | 120 A for the configuration shown on its product page | 20 A |
| Continuous Discharging Current | 81 A | 120 A for the configuration shown on its product page | 150 A |
| Key Platform Capability | 50 mA typical passive balancing with cell monitoring and battery history access | Charge-powered battery heating with multi-point temperature monitoring and history storage | 70 mA typical passive balancing with three cell, one MOS and one connector temperature channels |
| Communication and Integration | Isolated CAN at 1 Mbps (default BMS ID 1) and Bluetooth data access | CAN, RS485 and UART interface options; confirm the selected Bluetooth and flight-controller protocol configuration | CAN at 1 Mbps (default BMS ID 1) and standard BLE; no RS485 or UART |
| Choose This Model When | Your pack is 12S and your system stays within 27 A continuous charging and 81 A continuous discharging | Your 12S pack needs the shown 120 A current configuration or charge-powered heating | Your 12S pack needs up to 150 A continuous discharge and no more than 20 A continuous charge |
| Request EF-006 Review → | View EF-007 Details → | View EF-013 Details → |
EF-006 UAV BMS INTEGRATION
Confirm Your
EF-006 Integration
Tell us about your 12S UAV battery pack, charger and flight controller. Our engineers can review EF-006 fit against its 50.4 V charging voltage, 27 A continuous charge, 81 A continuous discharge and communication requirements.

EF-007
12S 120A Smart UAV BMS
EF-013
12S 150A Smart UAV BMS